Does the suction power in your Dyson Ball vacuum seem to be missing? Here’s how to clean a Dyson Ball vacuum and get it working like new again. A blockage or dirt accumulation could be the cause of your Dyson Ball’s stopping behavior if it has begun to lose suction strength or if the thermal cut-off keeps happening. A thorough cleaning is generally an easy fix.
Although the Ball Animal 2 will be used as an example in this guide, any upright Dyson Ball can follow the same procedure.
Step 1: Inspect For Obstructions In The Main Suction Tubes
Make sure your Dyson vacuum is turned off and unplugged before starting to clean it. Since you’ll be disassembling the vacuum, it’s critical that there be no chance of electric shock. First, take out the canister and make sure there are no obstructions in the main suction tubes. It is crucial to check the entrance and exit tubes from the canister since they may have clogs or blockages that might significantly reduce suction force.
After the dust canister is removed, you may usually inspect these three locations:
- The dust canister’s entrance vent.
- The tube that leaves the canister of dust.
- A third tube that’s frequently concealed by a clear hatch.
Step 2: Look For Obstructions In The Brush Roll.
The brush roll is one of the most typical locations for a tangle or obstruction. To remove the bottom plate, flip the two tabs after detaching the floorhead from the main vacuum. You’ll have simple access to the full brush roll as a result. Next, trim any string hair that has gotten tangled in the brush roll with a pair of scissors. Even though pet hair gets tangled in the brush roll of every vacuum, it’s crucial to take this step if you have pets or long-haired family members.
Step 3: Dust Canister Cleaning.
In order to thoroughly clean the dust canister, you should first take the cyclones out. To accomplish this, apply pressure to the clasp located at the top of the cyclone and then utilize the button located on the canister’s side to release the cyclones. You should only wipe the inside of the dust canister with a moist cloth after it has been separated. According to Dyson, you shouldn’t use any air fresheners or detergents in the canister.
Examine the cyclones when cleaning the canister is complete:
The cyclones are surrounded by a thin mesh that frequently becomes blocked with fluff. If so, remove it gently with a soft, damp cloth to restore suction.Prior to reassembling the vacuum cleaner, make sure the cyclones and canister are completely dry. Lastly, confirm that the main suction tube entrance is unobstructed. Next, put the floorhead back together and reattach it to the vacuum.
Step 4: Look For Clogs In The Hose And Wand.
After taking the wand off, visually check it for obstructions. After that, check the hose to see if there are any obstructions. To check whether there are any clogs farther down the hose, you might also try (gently) putting the end of a broomstick through if you can remove the hose. If you don’t want to take the hose out, you can visually extend it section by section while searching within for any cracks or darker blockages.
Step5: Clean The Two Filters.
Usually, the Dyson Ball series comes with two replaceable filters. In the event that either of them gets clogged, there will be a significant decrease in the amount of air passing through the vacuum. On top of the cyclones is where the first filter is situated. Detaching the dust canister and releasing a clasp to reveal the tubular filter will allow you to remove it. After giving it a thorough rinse in cold water until it runs clear, wring out any remaining liquid and let it air dry.
The ball itself contains the second filter. You must detach the ball’s side and lay the vacuum on its back in order to access it. The filter is actually made up of two parts: an outer shell and a foam ring. You should wash each portion individually. Once more, you can use cold water to rinse the filter; nevertheless, do not squeeze this filter dry.
Dyson generally advises cleaning the Ball Animal 2’s two filters at least once a month.Prior to reinstalling the filters in the vacuum cleaner, you should always give them a minimum of 24 hours to adjust. A moist filter runs the risk of drawing water into the vacuum’s motor, clogging more quickly, and allowing bacteria to proliferate.
FQAs:
How Are Dyson Filters Cleaned?
First, take the Dyson filters out. 2. Take out any extra powder. To get rid of extra dust, gently tap the filter against a sink or other container. 3. Clear the filter Use fresh water to clean the filter. Avoid using detergents. 4. Eliminate extra water Pour new water into the filter. To get rid of extra dirt, wet the two ends of the filter and shake it.
How Frequently Should The Filter On A Dyson Vacuum Be Cleaned?
Washing the filters at least once a month helps to preserve optimum performance, the vacuum’s suction force, and should increase the filter’s longevity.
How May Hair Be Taken Out Of A Dyson Vacuum?
To remove them, take a pair of scissors (manicure scissors work best). Cut along the bar. Avoid pulling or pushing any hairs loose, since this may cause harm to the vacuum. While trimming, take care not to harm the bristles. To get to the brush roll on some Dyson vacuums, you might have to remove the soleplate.
How Is A Dyson Restored?
Disassembling a Dyson and cleaning every millimeter to like-new condition is the only way to repair it and get rid of symptoms like these. Though laborious, it’s simple enough for anyone to perform; nonetheless, most people just take them to the repair shop.
Wrap Up
Although cleaning a Dyson Ball vacuum isn’t tough, it’s necessary to keep the suction going. It’s critical to locate and clear any possible obstructions because even a small clog can result in suction loss or the engine cutting out.
