To keep debris in the water line from entering the washer, filters are installed on the hot and cold intake water lines of clothes washers. These filters may need to be cleaned as they fill with silt and sand over time.

How To Clean The Water Lines’ Filters In A Clothes Washer:

How To Clean The Water Lines' Filters In A Clothes Washer

  • Switch off the washer’s water supply.
  • On the rear of the washer, unscrew the hot and cold hoses.
  • Use a spray bottle to squirt water onto the washer’s filters.
  • To get rid of any last bits of debris or grime, use a strong acid brush.
  • Reattach the washer’s hot and cold hoses.
  • Restart the water and look for any leaks.

After your washing machine has finished spinning, if your garments are still drenched, a dirty filter may be the cause. Fortunately, cleaning the filter in your washing machine is a quick and simple process. This post will explain where your filter is located in your front-loading or top-loading washer and how to clean it of debris and lint.

Locate the filter and unplug your computer. For front-loading machines, look at the bottom right corner and the outside. In machines with top loading, check underneath the agitator.

Take out the filter and use a fresh paper towel to remove any lint.

After removing the filter’s screen, give it a 10-minute soak in hot water.

Every three months, clean the filter in your washing machine.

Shut Down And Disconnect The Washing Machine:

It’s crucial to turn off your computer before finding and removing your filter. If your machine has a “Off” button, press it first. Alternatively, turn all of the buttons to a neutral position. After that, disconnect your washer from the wall outlet and switch off the electricity.  After cleaning, place the plug in a secure spot where it won’t become wet. Place some old towels in front of your washer so that any water that gets trapped in the filter can be absorbed.

Locate The Filter For Your Washing Machine:

Locate The Filter For Your Washing Machine

The filter on front-loading washers is often located outside the machine at the lower right corner. Examine behind the agitator to see  if your top-loading machine has a self-cleaning filter. In the lower right corner of the machine, look for your filter on older top-loading washers.   The component that revolves back and forth in the machine’s center throughout the washing cycle is called the agitator.

Even self-cleaning filters require cleaning every three to four months.

Your filter usually has a rectangular or circular cover over it if it is located in the machine’s lower right corner. See your machine’s handbook if you can’t find where to put your filter.

Take Off Your Filter’s Cover:

To remove the cover, just grab it and pull it away from your computer. If the cover on your machine has been childproofed, pull it off with a thin instrument, such a screwdriver. After that, rotate the lid counter-clockwise until it completely comes off.

Remove the agitator first on top-loading washers that have the filter underneath the agitation. Remove the agitator’s cap, then reach inside the shaft with your hand until you feel a wing-nut screw. Lift the agitator off after turning the screw counterclockwise until it comes out. Lift the filter cover out of its original place after removing the agitator.

Remove The Filter From Your Device:

Remove The Filter From Your Device

Once the cover is removed, just remove the filter from your machine. Wiggle and move the filter around as much as you can if it becomes stuck. This aids in removing any detergent or lint that might be causing it to stick.

You’ll probably notice a layer of detergent- and damp lint-mixed debris as you remove your filter.

The drainage hose is situated just in front of the filter in certain washers. Remove the drain pipe and remove the filter if it is preventing it from exiting.

Start The Cleaning Process:

To remove any lint from the filter, use a paper towel. Lint and extra detergent  on your filter are caused by an accumulation of extra detergent combined with lint. Wipe the screen with a fresh paper towel to get rid of it.  If the lint coating is thicker than usual, use a tiny brush, like an old toothbrush, to brush away the particles.

After removing the filter’s screen, give it a 10-minute soak in hot water. Remove your detachable lint screen and immerse it in a bowl filled with hot tap water. Any detergent, fabric softener, or lint that isn’t easily cleaned with a paper towel can be removed by soaking it.  If the screen won’t come off the filter, run hot water through the filter until all of the residue is gone.

Check the machine’s interior for any extra lint. Look inside the machine for any stray lint before changing the filter. Use a paper towel or a moist sponge to clean the washer’s drum if there is any lint present.

If your filter is located in the machine’s lower right corner, check the drainage pipe for lint and remove it. Usually, the hose is right next to or in front of where you took the filter off.

Change the outer cover and the filter. Reinstall your filter in the machine when it has been cleared of all residue. Since it gets wet when you use your washer, there’s no need to let it dry. Replace the drainage hose if you took it out before fastening the cover.

Replace the filter in its designated location and tighten the cover if it is beneath the agitator. After positioning the agitator above the filter, tighten the agitator’s cap and wing-nut.

To check for leaks, do a cycle with the washer empty. Make sure you reattached the lid and filter correctly before starting your daily washing. You just need to run a short cycle in your washer to accomplish that. Simply leave your washer empty while the cycle is running. The filter on your washer is not installed correctly if it is leaking.

In case the drainage hose needs to be taken out, make sure it is securely fastened, since it can possibly be the source of the leak.

This Is How Your Filter Lasts Long:

At least four times a year, clean your filter. Every three months, it is advised that you clean your filter. The filter needs to be cleaned on a regular basis since it gathers hair, change, and tissues. If you don’t have time to give your filter a complete cleaning every three months, make sure to periodically check for any potential buildup.  Regular filter cleaning also helps your washing machine last longer.

Another reason your washing machine can smell is a filthy filter.

Recognize issues as soon as they arise. Observe any indications that your filter need cleaning. Taking proactive measures to address your washer’s issues keeps it in excellent condition and spares you from having to cope with a washer that breaks down in the middle of a cycle.  A blocked filter is often indicated by excessive vibrations, damp garments after the last spin, or issues with the water draining.

Every time you use the door, wipe the seal off. Anything lodged in the door seal has the potential to become caught in your filter, even with routine filter cleaning. Depending on when you last cleaned the seal, this residue may clog your filter. This can shorten the filter’s life and frequently make cleaning more difficult.

Therefore, after every wash, wipe the exposed portion of the door seal with a rag to avoid clogging. The washer door’s innermost rubber component is called the door seal. When the washer is full, this component prevents water from escaping.

FAQs:

How May Lint Be Taken Out Of A Washing Machine?

Locate the filter and unplug your computer. For front-loading machines, look at the bottom right corner and the outside. In machines with top loading, check underneath the agitator. Take out the filter and use a fresh paper towel to remove any lint. After removing the filter’s screen, give it a 10-minute soak in hot water.

In What Location Does A Washing Machine Filter?

The filter on front-loading washers is often located outside the machine at the lower right corner. Examine behind the agitator to see  if your top-loading machine has a self-cleaning filter. In the lower right corner of the machine, look for your filter on older top-loading washers.

How Is A Washing Machine Drawer Cleaning?

Make sure the washing machine drawer is clean. You can take care of other things in the interim. Remove the detergent drawer from your machine and soak it in a hot, soapy water solution. Use a toothbrush to scrub out any hard-to-reach spots and remove any leftover fabric softener or detergent. Replace it after cleaning.

Conclusion:

It’s really simple to clean the washing machine’s filter. Make sure the washing machine is completely powered off by unplugging it first. Place a towel underneath the water supply after unscrewing it. Now release the water through the pipe by opening the service flap. The pump cover and fluff filter should then be unscrewed.

Scroll to Top